-
Notifications
You must be signed in to change notification settings - Fork 3
/
Copy pathhwdef-Sofirn_LT1S-Pro.h
114 lines (88 loc) · 3.16 KB
/
hwdef-Sofirn_LT1S-Pro.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
#ifndef HWDEF_SOFIRN_LT1S_PRO_H
#define HWDEF_SOFIRN_LT1S_PRO_H
/* BLF LT1S Pro driver layout using the Attiny1616
Driver pinout:
* eSwitch: PA5
* Aux LED: PB5
* WW PWM: PB0 (TCA0 WO0)
* CW PWM: PB1 (TCA0 WO1)
* Red PWM: PB2 (TCA0 WO2)
* Voltage: VCC
*/
#define LAYOUT_DEFINED
#ifdef ATTINY
#undef ATTINY
#endif
#define ATTINY 1616
#include <avr/io.h>
#define PWM_CHANNELS 1
#ifndef SWITCH_PIN
#define SWITCH_PIN PIN5_bp
#define SWITCH_PORT VPORTA.IN
#define SWITCH_ISC_REG PORTA.PIN2CTRL
#define SWITCH_VECT PORTA_PORT_vect
#define SWITCH_INTFLG VPORTA.INTFLAGS
#endif
// usually PWM1_LVL would be a hardware register, but we need to abstract
// it out to a soft brightness value, in order to handle tint ramping
// (this allows smooth thermal regulation to work, and makes things
// otherwise simpler and easier)
uint8_t PWM1_LVL;
// warm tint channel
#ifndef PWM1_PIN
#define PWM1_PIN PB0 //
#define TINT1_LVL TCA0.SINGLE.CMP0 // CMP1 is the output compare register for PB0
#endif
// cold tint channel
#ifndef PWM2_PIN
#define PWM2_PIN PB1 //
#define TINT2_LVL TCA0.SINGLE.CMP1 // CMP0 is the output compare register for PB1
#endif
// red channel
#ifndef PWM3_PIN
#define PWM3_PIN PB0 //
#define PWM3_LVL TCA0.SINGLE.CMP2 // CMP2 is the output compare register for PB2
#endif
// average drop across diode on this hardware
#ifndef VOLTAGE_FUDGE_FACTOR
#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V
#endif
// lighted button
#ifndef AUXLED_PIN
#define AUXLED_PIN PIN5_bp
#define AUXLED_PORT PORTB
#endif
// with so many pins, doing this all with #ifdefs gets awkward...
// ... so just hardcode it in each hwdef file instead
inline void hwdef_setup() {
// set up the system clock to run at 10 MHz instead of the default 3.33 MHz
_PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
//VPORTA.DIR = ...;
VPORTB.DIR = PIN0_bm | PIN1_bm | PIN2_bm | PIN5_bm; // Outputs: Aux LED and PWMs
//VPORTC.DIR = ...;
// enable pullups on the unused pins to reduce power
PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc; // eSwitch
PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // warm tint channel
//PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // cold tint channel
//PORTB.PIN2CTRL = PORT_PULLUPEN_bm; // red LEDs
PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
// set up the PWM
// TODO: add references to MCU documentation
TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_CMP2EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
TCA0.SINGLE.PER = 255;
TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
}
#endif